DIE STRUCK ALUMINUM Id Plates

• IMPRINTING METHOD: Die Struck and color-filled.
Reverse imprinting is not recommended. Printed features
should be a minimum 1/8" from edge of plate.

• MATERIAL : .050 thick Silver or Gold anodized aluminum.

• EXACT PLATE SIZES: A tolerance of + or - 1/32" must be
allowed on all plates.
This is extremely important to customers
who will placing the plates into a recessed area
that the plate must fit.
A product proof is recommended if the plate
must fit into something.

•MOUNTING HOLES: Holes must be
located on corners or edge of plates.
For holes in other locations call factory.
Exact hole placement is not guaranteed: A tolerance of + or -
1/64" to edge of plate or + or - 1/32" for hole center
to center must be allowed . Order a larger hole than needed
to compensate for this: e.g. need a 3/32" hole , order a 1/8"
hole to allow for the tolerances. This is extremely important
to customers who will mounting plates on equipment with pre-drilled holes where the plate must match. A product proof is recommended in the instance. HOLE SIZES AVAILABLE
3/32", 1/8", 5/32, 3/16", 1/4"

•ROUNDED CORNERS: Sizes available:

•PRESSURE SENSITIVE MOUNTING TAPE:
Standard two-way tape is intended for clean, dry, smooth
and flat surfaces. 1/32" thick foam two-way tape is for clean, dry and flat surfaces that are lightly textured. If unsure, contact factory
for random samples to test on your application.

•CONSECUTIVE NUMBERING:

50	100	250	500	1000	2500	5000	10000
.80	.70	.40	.36	.30	.28	.24	.20 8(C)

•EXTREME CONDITIONS: For exposure to excessive heat,
oils, salt water, solvents etc., contact factory before ordering.

•PACKAGING: Individual Poly bags.

•LESS THAN MINIMUM: Absolute minimum quantity 125 pieces. Add $65(C) if item is under $2.00 and $40(C) if over
$2.00 LTM charge. Multi-color imprints are not available on LTM orders.

•PRODUCTION TIME: 5-10 Working Days.
Call factory if a deadline is required.

•SET UP CHARGE: $60(G)

SET-UP CHARGE -Stamped (when camera ready art is supplied) $60 (G) per imprint color per side of imprint

Contact - Home

ID Plates-1-3.9 Square Inches-ST (Die Struck/Color Filled)	250	500	1000	2500	5000	Class	Wt/100
STID-1 to 3.9 Square Inches-ST (Silver)	1.48	1.43	1.24	1.06	1.02	2AB2C	2.4 LB
Add per Plate for Gold	0.13	0.12	0.11	0.10	0.08	5 G
Add for Each Additional Color Die Struck	0.51	0.46	0.42	0.38	0.32	5 G
Add per Plate for Two Way Tape	0.43	0.42	0.41	0.38	0.37	5 G	.24 LB
Add per Plate for Foam Two Way Tape	0.49	0.48	0.46	0.45	0.43	5 G	.24 LB
Add per Plate for Four Holes	0.30	0.29	0.27	0.26	0.25	5 G
Add per Plate for Rounded Corners	0.27	0.26	0.25	0.24	0.23	5 G

ID Plates-4-6.9 Square Inches-ST (Die Struck/Color Filled)	250	500	1000	2500	5000	Class	Wt/100
STID-4 to 6.9 Square Inches-ST (Silver)	1.86	1.81	1.57	1.39	1.34	2AB2C	3.9 LB
Add per Plate for Gold	0.24	0.23	0.21	0.20	0.19	5 G
Add for Each Additional Color Die Struck	0.51	0.46	0.42	0.38	0.32	5 G
Add per Plate for Two Way Tape	0.50	0.48	0.46	0.45	0.43	5 G	.39 LB
Add per Plate for Foam Two Way Tape	0.61	0.60	0.57	0.56	0.55	5 G	.39 LB
Add per Plate for Four Holes	0.30	0.29	0.27	0.26	0.25	5 G
Add per Plate for Rounded Corners	0.27	0.26	0.25	0.24	0.23	5 G
ID Plates-7-9.9 Square Inches-ST (Die Struck/Color Filled)	250	500	1000	2500	5000	Class	Wt/100
STID-7 to 9.9 Square Inches-ST (Silver)	2.21	2.16	1.90	1.69	1.64	2AB2C	5.4 LB
Add per Plate for Gold	0.35	0.33	0.32	0.31	0.30	5 G
Add for Each Additional Color Die Struck	0.51	0.46	0.42	0.38	0.32	5 G
Add per Plate for Two Way Tape	0.56	0.55	0.54	0.51	0.50	5 G	.54 LB
Add per Plate for Foam Two Way Tape	0.74	0.71	0.70	0.69	0.67	5 G	.54 LB
Add per Plate for Four Holes	0.30	0.29	0.27	0.26	0.25	5 G
Add per Plate for Rounded Corners	0.27	0.26	0.25	0.24	0.23	5 G
ID Plates-10-14.9 Square Inches-ST (Die Struck/Color Filled)	250	500	1000	2500	5000	Class	Wt/100
STID-10 to 14.9 Square Inches-ST (Silver)	2.80	2.72	2.40	2.11	2.02	2AB2C	7.9 LB
Add per Plate for Gold	0.52	0.51	0.50	0.49	0.48	5 G
Add for Each Additional Color Die Struck	0.56	0.52	0.45	0.43	0.38	5 G
Add per Plate for Two Way Tape	0.67	0.66	0.64	0.63	0.61	5 G	.79 LB
Add per Plate for Foam Two Way Tape	0.92	0.90	0.89	0.88	0.86	5 G	.79 LB
Add per Plate for Four Holes	0.30	0.29	0.27	0.26	0.25	5 G
Add per Plate for Rounded Corners	0.27	0.26	0.25	0.24	0.23	5 G
ID Plates-15-19.9 Square Inches-ST (Die Struck/Color Filled)	250	500	1000	2500	5000	Class	Wt/100
STID-15-19.9 Square Inches-ST (Silver)	3.19	3.09	2.74	2.43	2.34	2AB2C	10.4 LB
Add per Plate for Gold	0.71	0.69	0.67	0.64	0.62	5 G
Add for Each Additional Color Die Struck	0.56	0.52	0.45	0.43	0.38	5 G
Add per Plate for Two Way Tape	0.79	0.76	0.75	0.74	0.71	5 G	1 LB
Add per Plate for Foam Two Way Tape	1.11	1.10	1.08	1.06	1.05	5 G	1 LB
Add per Plate for Four Holes	0.30	0.29	0.27	0.26	0.25	5 G
Add per Plate for Rounded Corners	0.27	0.26	0.25	0.24	0.23	5 G
ID Plates-20-24.9 Square Inches-ST (Die Struck/Color Filled)	250	500	1000	2500	5000	Class	Wt/100
STID-20-24.9 Square Inches-ST (Silver)	3.52	3.44	3.04	2.72	2.64	2AB2C	12.9 LB
Add per Plate for Gold	0.89	0.87	0.85	0.82	0.80	5 G
Add for Each Additional Color Die Struck	0.56	0.52	0.45	0.43	0.38	5 G
Add per Plate for Two Way Tape	0.92	0.90	0.89	0.88	0.86	5 G	1.29 LB
Add per Plate for Foam Two Way Tape	1.33	1.31	1.30	1.29	1.26	5 G	1.29 LB
Add per Plate for Four Holes	0.30	0.29	0.27	0.26	0.25	5 G
Add per Plate for Rounded Corners	0.27	0.26	0.25	0.24	0.23	5 G
ID Plates-25-35 Square Inches-ST (Die Struck/Color Filled)	250	500	1000	2500	5000	Class	Wt/100
STID-25-35 Square Inches-ST (Silver)	4.70	4.58	4.06	3.60	3.50	2AB2C	17.9 LB
Add per Plate for Gold	1.12	1.08	1.05	1.01	0.98	5 G
Add for Each Additional Color Die Struck	0.73	0.61	0.53	0.44	0.41	5 G
Add per Plate for Two Way Tape	1.10	1.08	1.07	1.05	1.04	5 G	1.79 LB
Add per Plate for Foam Two Way Tape	1.63	1.61	1.60	1.58	1.57	5 G	1.79 LB
Add per Plate for Four Holes	0.30	0.29	0.27	0.26	0.25	5 G
Add per Plate for Rounded Corners	0.27	0.26	0.25	0.24	0.23	5 G